NEMA34 86mm Electronic Motor Brake MAB34x
|
Electronic brake for all NEMA34 motors
The electronic brake is designed to be mounted on step- and servo motors, such as the MIS340,MIS341,MIS342 series of integrated stepper motors and MST340, MST341,MST342 series of stepper motors without build in controller.
A high quality electro-magnetic brake is mounted inside the housing. The brake has zero backlash and no auditory noise. It fits on all step- and servo motors with NEMA3486x86mm flange and optional 9.35mm and 14mm shaft. The brake is used when it is desired to hold the motor shaft fixed at power off, or when the motor is used in a vertical linear application. When 24 VDC is connected, the brake will be deactivated and the motor can turn freely. It is recommended to use the brake only as a holding brake and not as an emergency brake.  |
|
 |
 |
 |
 |
 |
|||||
| Holding Torque [Nm] (Oz-In) |
Input Shaft Ø [mm] (inch) |
Output Shaft Ø [mm] (inch) |
Connection | IP Current@24VDC [Amp] |
Weight ex. cable [kg] (lb.) |
Lenght [mm] (inch) |
Photo | |
| MAB34X-91 | 1.7 (240.740) |
9.53 (0.375) |
9.53 (0.375) |
Wire 470mm | IP44 0.23 Amp |
1.35 (2.98) |
Max 78 (3.070) |
 |
| MAB34X-92 | 1.7 (240.740) |
9.53 (0.375) |
9.53 (0.375) |
M8 | IP55 0.23 Amp |
1.35 (2.98) |
Max 78 (3.070) |
|
| MAB34X-93 | 1.7 (240.740) |
14 (0.551) |
14 (0.551) |
M8 | IP55 0.23 Amp |
1.42 (3.13 ) |
Max 82 (3.228) |
 |
| MAB34X-94 | 1.7 (240.740) |
12.7 (0.5) |
12.7 (0.5) |
M8 | IP55 0.23 Amp |
1.42 (3.13 ) |
Max 82 (3.228) |
|
| Cable for MAB34 (except MAB34x-91) WI1000-M8F4A05N. |
||||||||
| MAB34M-4.0N05F05 | 4.0 (240.740) |
14 (0.551) |
14 (0.551) |
M8 | IP42 0.5 Amp |
2.02 (4.44) |
108.5 (4.27) |
 |
For recommended torque for shaft collar screw please read this document
Cables
| Part number |
Description | Drawing | Photo |
| WI1000-M8F4S.3N | M8 Cable 4 pin Fem 0° Shielded 0.3 m open end cable with straight connector |
 |
 |
| WI1000-M8F4AxxN xx: 05 meter or 10 meter |
M8 Cable 4 pin Fem 90° 5-10 m open end cable with angled connector |
|
|
|
Below cables are only for MIS Stepper Motors |
|||
| WI1013-M12M17TF4T.4N | M12 17pM M8 4pF for MABxx brakes 0.45m cable with M8 for brake and M12 for motor for direct connection |
 |
 |
| WI1013-M12M17TF4TXAA | M12 17pM M8 4pF for MABxx brake +2m cable 0.45m cable with M8 for brake and M12 for motor for direct connection including 2 meter cable with I/O 1-3 and CVO. |
 |
 |
Pin 1 blue = 0 VDC, Pin 2 brown = +24 VDC, Pin 3 black = NC, Pin 4 white = NC.
|
DETAILED
|
|
|
|
DOWNLOAD
|
JVL A/S Bregnerødvej 127 DK-3460 Birkerød Denmark
Tel: +45 4582 4440 Fax: +45 4582 5550 E-mail: jvl@jvl.dk
Tel: +45 4582 4440 Fax: +45 4582 5550 E-mail: jvl@jvl.dk
